• Forums
    • Public Forums
      • Community Connect
      • Dynatrace
        • Dynatrace Open Q&A
      • Application Monitoring & UEM
        • AppMon & UEM Open Q&A
      • Network Application Monitoring
        • NAM Open Q&A
  • Home /
  • Public Forums /
  • Application Monitoring & UEM /
  • AppMon & UEM Open Q&A /
avatar image
Question by Jan-Hendrik W. · Jan 28, 2014 at 11:28 AM ·

Web Request Dashlet and Measure

Hi,

 

I have a little problem understanding the web request time measure.

I want to get some historical graphs for reporting for some webrequests from the Web Request Dashlet. My understanding is, that I need a measure for it in this case.

I used the webrequest time measure, but when I compare the two values they are completely different.

On the left there are the measure from my measure and on the right you see the oob dashlet. Both uses the same filter.

 

What do I have to do to get the same values? Why am I not possible to drill down to PurePaths by using the measures.

 

Hope you can help me,

 

Jan

 

 

 

Comment

People who like this

0 Show 0
10 |2000000 characters needed characters left characters exceeded
  • Viewable by all users
  • Viewable by moderators
  • Viewable by moderators and the original poster
  • Advanced visibility
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 10 attachments (including images) can be used with a maximum of 50.0 MiB each and 250.0 MiB total.

4 Replies

  • Sort: 
  • Most voted
  • Newest
  • Oldest
avatar image

Answer by Jan-Hendrik W. · Jan 28, 2014 at 02:31 PM

Well, I already realized for other measures, that there was a small difference between PurePath and PW, but in this case, the difference is too high and in most cases, there are no data captured.

 

 

 

When I got you right, the two data should be the same, so that my assumption was correct. So, there must be an error in my measure evaluation.

Can it depend to the point, that the web requests are not entry points?

Jan

Comment

People who like this

0 Show 0 · Share
10 |2000000 characters needed characters left characters exceeded
  • Viewable by all users
  • Viewable by moderators
  • Viewable by moderators and the original poster
  • Advanced visibility
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 10 attachments (including images) can be used with a maximum of 50.0 MiB each and 250.0 MiB total.

avatar image

Answer by Klaus E. · Jan 28, 2014 at 02:20 PM

Can you set the time frame not to the last 5 minutes but the 5-10 minutes before? and additionally show the count in the charts on the left? The thing is that you are looking at 2 different data sources - on the Web Request dashlet you see the data from the continuous session storage so you are looking at the actual PurePath data. this data is calculated on demand when you query the time frame whereas on the left charts you are looking at Performance Warehouse data which is written into the Performance Warehouse every minute. There should not be a big difference but if you look at small time frames with the last option this could happen.

Klaus

Comment

People who like this

0 Show 0 · Share
10 |2000000 characters needed characters left characters exceeded
  • Viewable by all users
  • Viewable by moderators
  • Viewable by moderators and the original poster
  • Advanced visibility
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 10 attachments (including images) can be used with a maximum of 50.0 MiB each and 250.0 MiB total.

avatar image

Answer by Jan-Hendrik W. · Jan 28, 2014 at 12:36 PM

Hi,

 

this is not the reason. (smile) The filter was set to 5 minutes and the measures have been created half an hour before.

 

Regards,

Jan

Comment

People who like this

0 Show 0 · Share
10 |2000000 characters needed characters left characters exceeded
  • Viewable by all users
  • Viewable by moderators
  • Viewable by moderators and the original poster
  • Advanced visibility
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 10 attachments (including images) can be used with a maximum of 50.0 MiB each and 250.0 MiB total.

avatar image

Answer by Klaus E. · Jan 28, 2014 at 12:34 PM

Hi,

Could it be that you have created the measures later than the time frame that you cover with the dashboard? You only get data for a measure after you have created it.

Klaus

Comment

People who like this

0 Show 0 · Share
10 |2000000 characters needed characters left characters exceeded
  • Viewable by all users
  • Viewable by moderators
  • Viewable by moderators and the original poster
  • Advanced visibility
Toggle Comment visibility. Current Visibility: Viewable by all users

Up to 10 attachments (including images) can be used with a maximum of 50.0 MiB each and 250.0 MiB total.

How to get started

First steps in the forum
Read Community User Guide
Best practices of using forum

NAM 2019 SP5 is available


Check the RHEL support added in the latest NAM service pack.

Learn more

LIVE WEBINAR

"Performance Clinic - Monitoring as a Self Service with Dynatrace"


JANUARY 15, 3:00 PM GMT / 10:00 AM ET

Register here

Follow this Question

Answers Answers and Comments

3 People are following this question.

avatar image avatar image avatar image

Forum Tags

dotnet mobile monitoring load iis 6.5 kubernetes mainframe rest api dashboard framework 7.0 appmon 7 health monitoring adk log monitoring services auto-detection uem webserver test automation license web performance monitoring ios nam probe collector migration mq web services knowledge sharing reports window java hybris javascript appmon sensors good to know extensions search 6.3+ server documentation easytravel web dashboard kibana system profile purelytics docker splunk 6.1 process groups account 7.2 rest dynatrace saas spa guardian appmon administration production user actions postgresql upgrade oneagent measures security Dynatrace Managed transactionflow technologies diagnostics user session monitoring unique users continuous delivery sharing configuration alerting NGINX splitting business transaction client 6.3 installation database scheduler apache mobileapp RUM php dashlet azure purepath agent 7.1 appmonsaas messagebroker nodejs 6.2 android sensor performance warehouse
  • Forums
  • Public Forums
    • Community Connect
    • Dynatrace
      • Dynatrace Open Q&A
    • Application Monitoring & UEM
      • AppMon & UEM Open Q&A
    • Network Application Monitoring
      • NAM Open Q&A